| 1 | Mounting rail, DIN EN 60715, Stainless steel, 2000 mm, untreated, order no : 1747350000 , type: TS 35X7.5 2M/CRN , manf: Weidmuller, used for New HPI Diesel control |
| 2 | HMI, Panelview plus 1250, Ethernet communication, 24Vdc input, Part No. 2711P-T12C4D8, Manf. ALLEN BRADLEY, used for New HPI Diesel control panels. |
| 3 | BEARING F.E., P/NO. 34C540192-701 , MODEL # 5K830944C13 , USED FOR G.E. CHARGE MOTOR 900 HP FRAME SIZE MOTOR 8309S |
| 4 | BEARING, D.E., P/NO. 34C540191-701 , MODEL # 5K830944C13 , USED FOR G.E CHARGE MOTOR 900 HP, FRAME SIZE MOTOR 8309S |
| 5 | Uninterruptible Power Supply, 5 KVA, Ac input: 480 VAC Nominal Voltage, 60 Hz, 3 phase, Input voltage range +/- 10%, Input frequency range +/- 5. |
| Ac output: 5 KVA, 120 VAC, single phase, output voltage +/- 2%, 60 Hz, 0.8 to 1 load power factor, THD not more than 5% with overload protection at 120%, and earth leakage indication. | |
| Equipped with static switch AC input 120 VAC, single phase. To transfer the load to reserve supply (Make before break) in case of loss of inverter square wave, inverter overcurrent, low AC output, Low DC disconnect or by manual operation with zero break criteria. Moreover, to enable the inverter outputs automatically after fault clearance. | |
| Equipped with Manual Bypass Switch, Zero-break (make - before - break) and to make the Synchronization with Bypass source. | |
| Cable entrance from button, Forced Ventilation Air Cooling, Ambient Temperature 40 C, Audible Noise not more than 65 dB @ 1.5 meters. | |
| Include a suitable monitor and mimic system to show the status of the internal circuit breakers, in addition input/output AC Ammeter and voltmeter, inverter loading meter, DC bus voltmeter, and KW loading. IP not less than IP21. | |
| In additional, the UPS should equipped with inverter output CB, Battery high interrupt CB, Lamp/alarm test buttons and suitable lifting I Bolts. | |
| Indication LED should be installed for out of synchronization, Inverter fuse blown, AC input available, Bypass input available, Inverter available and charger available. | |
| The UPS should be provided including its batteries that should cover the full load for not less than one hour. | |
| Provided with their cables 50m, as the batteries will be in remote room. | |
| Manufacture: AMETEK Solidstate Controls CO. Used for Sh-Ali platform ESD circuit | |
| manufature :-AMETEK Solidstate Controls CO. | |
| 6 | CABLE, POWER/CONTROL ARMOURED 6 AWG 4 COPPER CONDUCTORS/90 C RATING 600 VOLT ALUMINUM SHEATH DIRECT BURIAL C-L-X TYPE MC (XHHW) "OKONITE" CAT. NO. 571-31-3270 |
| 7 | Panel Board , Three phase , four wire ,208/120V , with main circuit breaker 240 VAC / 100 A Top mounted , maximum No. of poles 18 ( including 3 pole (30 A) ,2 pole (20A) , 1 pole (20A) , Cat. No. PRL1A310018C & Box NEMA 1 EZB2036R , Manuf. EATON , used for R/SH Camp. |
| 8 | Scotch Super 33+ Vinyl Electrical Tape is based on polyvinyl chloride (PVC), 7 mils thick, marked per UL Standard 510 as Flame Retardant, Cold and Sunlight Resistant. operation voltage 600 Volt , 60 HZ , PN : 33+SUPER-3/4X66FT , Manf. 3M (Package = 10 Each) |
| 9 | Sylvania lamp Part No: H34GW-1000/DX, manufacture: PHILIPS, Mercury Vapor Light Bulb. Sylvania 1000 watt BT56,Coated Brite White Deluxe Mogul Screw (E39) Base 4000K High Current Mercury |
| 10 | Fixture, lighting, high pressure sodium (HPS), 400 W, 480 V, 60 Hz, CAT No. FMVSY400/480/S826TB/SFA6, protection rating of NEMA 4x, class 1 Div 2, fits onto 2" pipe, Manf. Cooper Crouse-Hinds |
| 11 | FIXTURE, LIGHTING MERCURY VAPOUR Ballast and Housing FOR WET LOCATIONS WITH GLOBE AND GUARD 120 VOLT. 175 WATT MNFG . CROUSE USA New part no.: VMVM175/MT XP |
| 12 | Terminator cable, Cable Gland ½" NPT, Cat. no. TMCX165-BR-NP, copper construction nickel plated, with cold shrink Cat. no. TMC-K1, with lock nut cat. no. CAP280124, used in hazardous locations Class I, Div. 1, Groups A, B, C, D, cable outer diameter range(0.490-0.781), Manuf. Crouse hinds. |
| 13 | Terminator cable, Cable Gland ¾ "NPT, Cat. no. TMCX285-BR-NP, copper construction nickel plated, with cold shrink Cat. no. TMC-K2, with lock nut cat. no. CAP280134, used in hazardous locations Class I, Div. 1, Groups A, B, C, D, cable outer diameter range(0.650-1.00), Manuf. Crouse hinds. |
| 14 | BOX, CONDUIT OUTLET 1/2" WITH COVER "CROUSE- HINDS" CAT.NO. GUAX-14 MNF. CROUSE HINDS USA |
| 15 | BOX, CONDUIT OUTLET 3/4" WITH COVER "CROUSE-HINDS" CAT.NO GUAX-24 MNF. CROUSE HINDS USA |
| 16 | Reducer, A-series, copper construction nickel plated, ½"F * ¾"M NPT, P/N. CAP 744884, used in hazardous locations, Manuf. Crouse hinds |
| 17 | Professional Use Premium Vinyl Electrical Tape, Super 88, Unprinted. Size: 3/4" Width, 66' Length. Thickness: 8.5 mils. Voltage Rating: 600V. Temperature Rating: 221°&Different colours (Yellow-Blue-Red-Black-Green) |
| 18 | TAPE, LOW VOLTAGE .030" THICK, 3/4" WIDTH, 30 FT LENGTH "OKONITE" CAT NO. 602-10-2010(DISCONTINUED ,USE 3M 130C,1"X30' |
| 19 | TAPE, "SCOTCHFIL" INSULATION PUTTY 1-1/2" WIDTH 60'LENGTH |
| 20 | CABLE TERMINATOR "GLAND" SIZE 1/2" WITH PVC COATING PT.NO. TMCX165-PVCCTD @ FOR AUTOMATION DEPARTMENT USE ONLY. |
| 21 | CABLE FITTING FOR HAZARDOUS ENVIRONMENT WITH 40 MI L PVC COATING, CROUSE HINDS TMCX165-PVC (CGSJ-110 1-PVC),NEW CAT.NO. |
| TERMINATOR CABLE, POTTING HEAD FOR JACKETED INTERLOCKED ARMORED "C-L-X" OR "CCW" CABLE MALE THD. 1/2" CABLE RANGE 0.625-0.875" ARMOR RANGE 0.500-0.625" FORM C-B "CROUSE-HINDS" CAT. NO. CGSJ-1101-PVC | |
| 22 | CABLE FITTING FOR HAZARDOUS ENVIRONMENT WITH 40 MI L PVC COATING. |
| TERMINATOR CABLE, POTTING HEAD FOR JACKETED INTER- LOCKED ARMORED "C-L-X" OR "CCW" CABLE MALE THREAD 3/4", CABLE RANGE 0.750-1.000", ARMOR RANGE 0.625 - 0.813 FORM C "CROUSE-HINDS" CAT. NO. TMCX 285-PVC @REF MEMO GEN MGR DTD 25/1/93 | |
| 23 | FUSE, 200.000 AMP INTERRUPTING, 3A 600 V, CURRENT LINITING, 3 AMPS. 'SHAWMUT' CAT. NO. A4J3. NEW CAT NO. JKS3 |
| 24 | FUSE, 1 AMP 600 V. LIMITRON QUICK ACTING BUSS NO. JKS1 |
| 25 | PLUG, EXPLOSION PROOF, 15 A, 125 V, 2 POLE, 3 WIRE, WITH GROUND WIRE, CRUOSE HINDS CAT NO. ENP5151. |
| 26 | LAMP, MERCURY 175 WATT MOGUL BASE SCREW DELUXE WHITE BULB BT28 CODE H175DX39-22 G.E. NO.HR175DX39 MFG." G.E." @ I.R. C/NO. 14-037350 |
| 27 | Box, terminal series 8150, order No: 8150/1-0600-0600-230-3321 (600mm x 600mm x 230mm), without flange, Ex e, internal terminal blok type MXK4 (46 each), complete with 2 each holes threaded 1/2" NPT from upper side and 2 each holes threaded 11/4" NPT from lower side, Manfacture:STAHL |
| 28 | Box, terminal series 8150, order No: 8150/1-0600-0400-150-3311 (600mm x 400mm x 150mm), without flange, Ex e, internal terminal blok type MXK4 (46 each), complete with 4 each holes threaded 3/4" NPT , 1 hole threaded1" NPT ,1 hole threaded,and 2 Each stopper plug 3/4" , Manfacture:STAHL |
| 29 | Variable Speed Drive, Input: 480 V, 51 A, 48-63 Hz, Output: 0~480 V, 55A, 0~300 Hz, IP21, P/N: ACS800-31-0040-5+E200+K458+R700, Mfg. ABB, parts for Saqqara VSD panels |
| 30 | HAWKE BARRIER CABLE GLAND TYPE 711 A 1/2" NPT SAQ-EL08-ONS-2435 CABLE AND GLANDS |
| 31 | CANDIS-10 board, part # RJ45 COUDE uC MB90F546, Supplier code: 5911110010, Manufacture CHLORIDE, used for Badri UPS UPS #2 (DT 316063) |
| 32 | CANDIS-10 board, part # RJ45 COUDE uC MB90F546, Supplier code: 5911110010, Manufacture CHLORIDE, used for Badri UPS UPS #1 (DT 316063) |
| 33 | Power Supply Unit, 220 Vdc, Out: +20 Vdc/ +12 Vdc/ +5 Vdc, Mfg. Gutor, used for all saqqara UPSs (gutor item no. : 0P0284 ) |
| 34 | Static Switch Module, PEW1~EN/EA, Iac=<100 Aac, Mfg. Gutor, used for saqqara offshore UPS (Gutor item no. : 0C0942 ) |
| 35 | Rectifier Module, Idc=<145 Adc, Type PXW, Mfg. Gutor, used for saqqara offshore UPS (Gutor item no. : 0C0949) |
| 36 | Contactor, 4 pole , Non Reversable, BF 20, 690 V, 8 KV, 40 A, Coil Voltage: 110 Vac, 50/60 Hz, Mfg. Lovato, Parts for Saqqara Fuel Gas Heater |
| 37 | Socket, Relay, Screw Terminal (Plate clamp) socket, 4 poles, P/N:94.74, Mfg. Finder, Parts for Saqqara Fuel Gas Heater |
| 38 | Miniature Circuit breaker one poles, Manf. Merlin grin, Multi 9 , type K60N ,C25,240/415 , Used for LDP in Badri P/F |
| 39 | CIRCUIT BREAKER' 140U-I6C, 3 POLE, 60A. Part # 140U-I6C3-C60-M(A), manufacture Allen Bradley, used for J10 MCC. |
| 40 | Miniature Circuit breaker, Manf. : Merlin grin, Multi # 9, 2pole , C60N, In 63Amp., 400Volt, 50Hz, ICU 10KA, IEC 60947 Part # 60887 , used for PDP # 2 Badri PDP ( power distribution panel ) |
| 41 | Circuit breaker, CUTLER HAMMER , 100 AMP,CAT ELHFD3100L,STYLE 6601C94G13,SERIES C, for Saqqara Onshore Low Voltage MCC |
| 42 | CIRCUIT BREAKER, 100 AMP 600 VAC 3-POLE THERMAL MAGNETIC FRAME TYPE FH "SQUARE D" CAT. NO. FHL36100 |
| 43 | MOTOR, ELECTRIC, TYPE DAM160LX10C, EXPLOSION PROOF, 460 V, 3 PHASE, 60 HZ, STAR CONNECTION 7KW, 690 RPM, POWER FACTOR 0.69, INSULATION CLASS F, TEMP 55 DEG C, PROTECTION IP55, CONTINUOUS DUTY, MOUNTING V3.with greasing pin (REF. AEG CO.). |
| 44 | CONTACTOR, 120 VAC, 3 POLE SIZE 3" CAT.NO.A201K3CA MNF. CUTLER HAMMER USA |
| 45 | CIRCUIT BREAKER, 90 AMP 600 VAC 3-POLE, "WESTINGHOUSE" CAT. NO. FD3090 MNF. CUTLER HAMMER USA |
| 46 | CONNECTOR, "HYLINK" TYPE YS-L COND. SIZE #6 STR. "BURNDY" CAT. NO. YS6C-L |
| 47 | CIRCUIT BRAKER, 25 AMP "WESTINGHOUSE" CAT.NO. HFD3025 MNF. CUTLER HAMMER USA |
| 48 | RELAY, TIME ON PICK-UP COIL 24 VDC TIME 20-200 SEC. "AGASTAT" MOD. NO. 7012-OE |
| 49 | RELAY, TIME DELAY ON PICK-UP COIL 24 VDC TIME 0-50 SEC. "AGASTAT" MOD.NO. 70120D NEW CAT NO. 1437446 MNFG. AGAST USA |
| 50 | CONTACTOR, 120 VAC 3 POLE SIZE 1, "WESTINGHOUSE" CAT.NO. A201K1CA MNFG. CUTILER HAMMER |
| 51 | KIT, CONTACT, A200 STARTER 3 POLE SIZE 3 "WESTINGHOUSE" STYLE NO. 626B187G13 |
| 52 | STARTER 3 PHASE 600 VAC. SERIES B SIZE MAX. AMP. 45 "FURNAS" CAT. NO. 14FP32AF81 |
| 53 | RELAY, SEALED UNIT SOLID STATE ICG-220 220 V. AC 50/60 HZ "THE HARRY ALTER" CAT. NO. 60568 NEW # IGC-1 |
| 54 | SUPPRESSOR DIODE ECG-5157. (MANUFACTURED BY PHILIPS ECG). (PF. BATTERY CHARGER LAMARCH MODEL A11B-40-130V-C3 S/N M-1274-3). (LA MARCH) |
| 55 | RELAY, TIME DELAY (ON-DELAY) 5-50 SEC. 24 VDC COIL AGASTAT" CAT. NO: 1437446-7 MNFG. AGASTAT |
| 56 | HEAT ELEMENT, OVERLOAD SERIES F "WESTINGHOUSE" CAT. NO. FH38 MNF. CUTLER HAMMER USA |
| 57 | HEAT ELEMENT, OVERLOAD SERIES F, FOR STARTER SIZE 00, "WESTINGHOUSE" CAT.NO. FH28P/N4713A57H28 MNF. CUTLER HAMMER USA |
| 58 | TAPE, MASKING, 3/4" WIDTH, 60 YD. LENGTH, "3M" CAT . NO. 232 |
| 59 | FUSE, 2 AMP BUSS CAT.NO. GMA2 MNF. BUSSMAN USA |
| 60 | LOCK NUT, CONDUIT 1", (CAT# L-300) APLETON CAT BL-100 MNFG. APPLETON |
| 61 | PanelView Plus computer located in the panel door. part # 2711P-T15C4D8. manufacture Allen Bradley, used for J10 switchgear |
| 62 | Battery type Z15E P/N D.60.B.Z15E |
| 63 | Battery type LZ15E long battery for iGauge5. P/N : D.60.B.LZ15E |
| 64 | Battery Z20E for high temp iGuage5 (only available from Metrolog part of tool set) |
| 65 | Fixture emergency, complete hazardous location unit, type : Z1250 - - - N1812 SD, 12 Volt DC, 50 watt, NEMA 4 & 4X, complete with two tungsten lamps type N1812 (12 VDC), suitable for hazardous area Class I Division II group A, B, C, D, Zone 2, Groups IIA, IIB+ H2 120/277 VAC dual-voltage with surge protected, solid state charging circuitry. Manufacture: LITHONIA LIGHTING |
| 66 | BATTERY, ( P/N: HNN-4002 ). USED FOR VHF TRANSCEIVER MOTOROLA GP-340 |
| 67 | BATTERY, SUNLYTE, PHOTOVOLTAIC 6 CEL,12 VOLT VALVE-REGULATED LEAD -ACID 100 AH MODEL 12-5000X,CW CARRYING HANDLE |
| 68 | CABLE, INSTRUMENTATION UL TYPE PLTC ARMORED 3/C NO. 16 OVERALL SHIELD 300 VOLT RATING OKONITE MODEL 564-15-3401 HWC#646001601 MNF OKO USA @(FOR AUTOMATION DEPARTMENT USE ONLY) |
| 69 | CABLE TERMINATOR "GLAND" SIZE 1/2" WITH PVC COATING PT.NO. TMCX165-PVCCTD @ FOR AUTOMATION DEPARTMENT USE ONLY. |
| 70 | LOCK NUT, CONDUIT 1/2",(CAT#L100) APLETON CAT.BL-50 MNFG.APPLETON |
| 71 | CHARGER,BATTERY 5A 120 VOLT AC INPUT 24 VOLT DC OU TPUT (MFG. LA MARCHE) P/N (A2OR524/32VA1) |
| 72 | BLOCK, TERMINAL TYPE SAKR., VOLTAGE RATING 300V., AMP. RATING 10 A CATALOG NO. 41212 "WELDMULLER TERMINATION INC" @(FOR AUTOMATION DEPARTMENT USE ONLY) |
| 73 | BLOCK,FUSE TERMINAL TYPE SAKR CATALOG NO 24892 "WELDMULLER TERMINATION INC" @ FOR AUTOMATION DEPT. USE ONLY |
| 74 | FUSE, 4 AMP "BUSS" CAT.NO. MDL4 @ FOR AUTOMATION DEPARTMETNT USE ONLY. MNFG. BUSS |
| 75 | FUSE ,3 AG FAST-AXTING, 6 AMP 1/4 X 1 1/4" STOCK NO. 27F662 REF.NEWARK CATALOG P/N. 27F662 MNFG. BUSSMAN |
| 76 | FUSE, 20 AMP. "BUSS" CAT.NO. MDL20 MNFG.BUSS |
| 77 | CHARGER, BATTERY, "LAMARCHE" MODEL A18J-3-12V-A1-- -PLAIN CHARGER |
| 78 | Tray cable plate CH6-SP / CH6-SPH90 / CH6-SPV90/SSNBW2-316 ( cable tray accessories) |
| 79 | Tray Cable tray Type CE Straight Section - E Profile [CE] (cable tray -CE121820) 20 ft |
| 80 | CABLE, CLAMP, "TY-RAP" SELF-LOCKING DIA RANGE 1/16" - 4", 'T & B' CAT NO TY-528M (PKG= 100 Pcs) |
| 81 | BATTERY, SUNLYTE, PHOTOVOLTAIC 6 CEL,12 VOLT VALVE-REGULATED LEAD -ACID 100 AH MODEL 12-5000X,CW CARRYING HANDLE |
| 82 | CABLE TERMINATOR "GLAND" SIZE 1/2" WITH PVC COATING PT.NO. TMCX165-PVCCTD @ FOR AUTOMATION DEPARTMENT USE ONLY. |
| 83 | LOCK NUT, CONDUIT 1/2",(CAT#L100) APLETON CAT.BL-50 MNFG.APPLETON |
| 84 | CHARGER,BATTERY 5A 120 VOLT AC INPUT 24 VOLT DC OU TPUT (MFG. LA MARCHE) P/N (A2OR524/32VA1) |
| 85 | BLOCK, TERMINAL TYPE SAKR., VOLTAGE RATING 300V., AMP. RATING 10 A CATALOG NO. 41212 "WELDMULLER TERMINATION INC" @(FOR AUTOMATION DEPARTMENT USE ONLY) |
| 86 | BLOCK,FUSE TERMINAL TYPE SAKR CATALOG NO 24892 "WELDMULLER TERMINATION INC" @ FOR AUTOMATION DEPT. USE ONLY |
| 87 | FUSE, 4 AMP "BUSS" CAT.NO. MDL4 @ FOR AUTOMATION DEPARTMETNT USE ONLY. MNFG. BUSS |
| 88 | FUSE ,3 AG FAST-AXTING, 6 AMP 1/4 X 1 1/4" STOCK NO. 27F662 REF.NEWARK CATALOG P/N. 27F662 MNFG. BUSSMAN |
| 89 | FUSE, 20 AMP. "BUSS" CAT.NO. MDL20 MNFG.BUSS |
| 90 | Tray cable plate CH6-SP / CH6-SPH90 / CH6-SPV90/SSNBW2-316 ( cable tray accessories) |
| 91 | Tray Cable tray Type CE Straight Section - E Profile [CE] (cable tray -CE121820) 20 ft |
